![]() ![]() Then specify either usb1 or usb2 in the boot command.Ĭopy the ACI image from the USB drive to the switch. If you have two USB drives, enter the dir command to see which drive contains the ACI image. Sequence (Ctrl-C or Ctrl-]) during the initial boot sequence to access theĭrive containing the ACI image into the standby supervisor USB slot.Įxample: loader> boot usb #: aci-image-name Note Need to copy and boot the ACI image for use with the replacement standby Replace the standby supervisor module in a dual-supervisor system, you will Replacement Standby Supervisor to ACI Boot Mode See the ACI and APIC documentation to configure and operate your switch in ACI mode. Need to install certificates for Cisco Nexus 9000 Series switches that were TAC to generate and install the correct certificates for your device. You must install certificates for your device.Įxample: openssl asn1parse -in /securedata/ssl/server.crt Integrity of the file by displaying the MD5 checksum.Įxample: switch(config)# show file bootflash: aci-image-name md5sum Do not run it after you enter theĪctive and standby supervisor modules with the ACI image.Įxample: switch(config)# boot aci bootflash: aci-image-name CautionĬopy running-config startup-config command after the Steps to copy the ACI image from the APIC:Īddress on the mgmt0 interface of the switch to allow connectivity between thisĮxample: switch(config)# feature scp-serverĪPIC CLI, use SCP to copy the firmware image from the APIC to the activeĮxample: scp -r /firmware/fwrepos/fwrepo/ switch-image-name switch-ip-address: switch-image-nameĭual-supervisor systems, copy the ACI image to the standby supervisor module.Įxample: switch(config)# copy bootflash: aci-image bootflash://sup-standby/Įxample: switch(config)# copy running-config startup-config NoteĬopy running-config startup-config command prior toīooting the ACI image. "n9000" while ACI filenames begin with "aci-n9000." NXOS image file name is: bootflash:///nxos.7.0.3.I1.2.binįilenames begin with "nxos" or ![]() Switch is running Cisco NX-OS Release 7.0(3)I1(2) or a later release. In the Cisco Nexus 9000 Series FPGA/EPLD Upgrade Release Notes. If any upgrades are required, follow the instructions Use the show install all impact epld epld-image-nameĬommand to verify that the switch does not require any EPLD image upgrades. Supervisor module is in the ha-standby state.Īpplication Policy Infrastructure Controller (APIC) is running Release 1.0(2j) Module command to make sure that the standby Mechanism before powering down the unsupported modules, which can cause delays Otherwise, the software uses a recovery/retry For example, line cards are not compatible between Cisco NX-OS and ACI boot mode.Ĭommand). ![]() Verify whether your switch hardware is supported in ACI boot mode by checking the "Supported Hardware" section of the Release Notes for Cisco Nexus 9000 Series ACI-Mode Switches. If you are converting to ACI boot modeįrom an earlier Cisco NX-OS release, follow the instructions in the To convert a Cisco Nexus 9000 Series switch running Cisco NX-OS Releaseħ.0(3)I1(2) or later to ACI boot mode. Converting a Replacement Standby Supervisor to ACI Boot ModeĬisco Nexus 9000 Series switch from Cisco NX-OS to ACI boot mode.Ī Cisco Nexus 3164Q or 31128PQ switch to ACI boot mode.Converting from Cisco NX-OS to ACI Boot Mode and from ACI Boot Mode Back to Cisco NX-OSĪ Cisco Nexus 9000 Series switch from Cisco NX-OS to Cisco Application Centric
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |